36KW模溫機,60KW模溫機廠家生產橡膠密封條擠出模溫機，三元乙丙發泡密封條擠溫機，PV膠條硅膠條冷喂料擠溫機，硅橡膠密煉機專用模溫機在膠條機必須采用耐高溫150℃以上喉管或波紋管，油管接駁鎖緊，并于開機后再檢查遍，以免松脫水源及散熱水塔周圍惡劣時，冷卻水回路必須安裝Y型過濾器，及定時清理，保證機器冷卻正常。總的來說，加熱能力愈強，則所需的升溫時間，便相應地了（加熱能力雙倍，升溫時間），往往就是因為模溫控制器的能力太低，引致模具不能達到佳的溫度狀態。欲想知道模溫控制器實際，我們可以比較它的實際的和計算的模具升溫時間。運行，了傳熱媒與油箱內傳熱媒的熱交換，油箱內的溫度，了傳熱媒的使用壽命；置于油泵吸油口側的放油、排污口，且在出口處配裝了球閥，放油、排污更快捷、方便電控結構更加合理。我公司在溫度控制技術上精益求精和不斷創新的新近更推出控溫精度達到±0.1℃的機型 ,使模具溫度控制機的運用有了更廣闊的空間。在耐高溫不銹鋼無縫管內均勻地分布高溫電阻絲，在空隙部分致密地填入導熱性能和絕緣性能均良好的結晶氧化鎂粉，加熱器這種結構不但先進，熱效率高，而且發熱均勻，當高溫電阻絲中有電流通過時，加熱器產生的熱通過結晶氧化鎂粉向金屬管表面擴散，再傳遞到被加熱件或空氣中去，達到加熱的目的。                     型號                          單位Unit                          JOS-05                          JOS-10                          JOS-20                          JOS-30                          JOS-50                          JOS-75                                控溫范圍                          ℃                          熱載體油常溫-300℃，普通水可至160度                                 溫控精度                                                   PID±1℃                                電源                                                   AC3∮380V 50HZ3P+E（5M）                                傳熱媒體                                                   熱媒油或導熱油或水                                冷卻方式                                                   間接冷卻 Indirect Cooling                                加熱功率                          KW                          6/9                          9/12                          18                          24/36                          48/60                          75                                泵匹數                          HP                         1                          2或3                          3                          3或4                          5或7.5                          7.5或10                                泵流量                          L/MIN                          98                          150                          235                          315                          367                          465                                電力                  消耗                          KW                          6.5/10                          10/13.5                          20                          27/39                          52/64                          81                                冷卻水配管                          INCH                          1/2                          1/2                          1/2                          1/2                          3/4                          3/4                                循環油配管                          INCH                          1/2                          1/2*2                          1/2*2                          1.2                          1.5                          2                                外型尺寸                          MM                          750*325                  *680                          750*325